SYSTEM: FIBERSHIELD® | MODEL: FIBERSHIELD®-I
| Type | Heat-insulating fire protection closure with textile design |
| Verification | CE marking according to EN 16034:2014 in conjunction with EN 13241:2003+A2:2016 |
| Closing direction | From top to bottom |
| Fire resistance | EI1 30 – EI2 120 | Tested according to EN 1634-1:2014-03 | Classified according to EN 13501-2:2016 |
| Smoke protection | Sa: for joint length 14.5 m for EI1 30 – EI2 120 | Tested according to EN 1634-3:2005-01 in connection with EN 1363-1:2012-10 | Classified according to EN 13501-2:2016 |
| Closing cycles | C0, C1, C2 | Tested according to EN 12605:2000-08 | Classified according to EN 13501-2:2016 |
| Fire behaviour of textile | B-s1, d0; E-d2 | Tested according to ISO 11925-2 and EN 13823 | Classified according to EN 13501-1:2018 |
| Environmental conditions | Special environmental conditions are not taken into account (e.g. humidity > 80 %, ambient temperature < 5 °C and > 45 °C, wind loads etc.). |
| Visible surfaces | galvanized | RAL, smooth, silk gloss, standard coour shade | Stainless steel type I V2A material A-1.4301 (bright) | Stainless steel type I V2A material A-1.4301, K240 (ground) | in each case for the visible surfaces of the housing and the guide rails |
Size dimensions and system structure
The combination of classifications or the ratio of clear system width to clear system height may reduce the stated maximum dimensions and the dimensions of the housing and guide rails may vary. The specifications on the quotation apply.
| Fire resistance/classifications | Size max.* [y x r] in mm | Fabric | Wall thickness* in mm | Housing | Guide rails |
| EI1 30/EI2 30 | 7315 x 3800 | Stratex 3 | 150 | Type A | Type 1 oder Type 3*** |
| EI1 30/EI2 30 | 7315 x 4950 | Stratex 3 | 150 | Type B | Type 1 oder Type 3*** |
| EI1 60 | 6600 x 4840 | Stratex 12 | 150 | Type B | Type 2 |
| EI2 60 | 4400 x 3400 | Stratex 6 | 150 | Type A | Type 1 oder Type 3*** |
| EI2 60 | 4400 x 4400 | Stratex 6 | 150 | Type B | Type 1 oder Type 3*** |
| EI2 60 | 6600 x 4840 | Stratex 9 | 150 | Type B | Type 1 |
| EI1 90 | 6000 x 4400 | Stratex 12 | 150 | Type B | Type 2 |
| EI2 90 | 6000 x 4400 | Stratex 9 | 150 | Type B | Type 1 |
| EI2 120 | 6000 x 4840 | Stratex 12 | 175 | Type B | Type 2 |
| Sa | Sa = joint length must not exceed 14.5 m (normative: 3-sided without end strip) | ||||
| C | 7315 x 4950 | Stratex 3, EI1 30/EI2 30 | |||
| C1 | 4400 x 4400 | Stratex 6, EI1 60 | |||
| 6000 x 4400 | Stratex 9, EI2 60 | ||||
| 6000 x 4400 | Stratex 9, EI2 90 | ||||
| C2 | 6600 x 4840 | Stratex 3, EI1 30/EI230 | |||
| 6600 x 4400 | Stratex 12, EI1 60/EI260 | ||||
| 6600 x 4400 | Stratex 12, EI1 90 |
The installation situation must comply with the building code requirements of the country of installation. The fire resistance of a ceiling or wall support structure and the adjacent components must at least correspond to that of the fire and/or smoke protection closure/fire and/or smoke protection curtain. Proof of the stability and serviceability of the adjacent walls and components must be provided under general ambient conditions and in the event of fire. See also notes on the standard supporting structure in EN1366-7:2004 or EN1363-1:2020. The fire protection system must not be subjected to any additional loads other than its own weight, even in the event of fire.
* Deviations from size dimensions on request
** tested wall types according to the installation instructions
*** Guide rails type 3 maximum size 3000 x 2870 mm and no continuous functions C1 & C2
